ca18det

  1. A

    Anyone with a CA18 S13 near Farnborough?

    Hi all, I've got a 1991 200sx which I bought as a rolling shell. I'm now in the process of putting in a CA18DET from another S13. I've got the engine in and I'm now trying to wire it up with the mess of wires I have. I'm missing quite a few bits which is making it quite difficult. I was...
  2. Yep_FK

    Wanted CA18DET Engine

    Looking for a CA18DET, Ideally decent spec or standard refreshed. Wanting supporting mods as well however can buy just an engine. Must be working and not need very much but open to offers. Must be able to be paleted to Kent
  3. M

    For Sale forged ca18det full swap

    hello, selling my forged ca18det with about 8k km, everything works just fine, compression is checked. selling as a full swap(gearbox, engine, ecu, harness, mounts, manifolds..etc). there is a lot to tell but the main mods are: ARP in all engine CP pistons K1 connecting rods acl sleeves 444cc...
  4. B

    suitable engine oil according to internal bearings tolerance

    hi guys,after a long time I'm almost ready to start my engine, it has been resting in my bedroom for far too long, I would like to have a comparison, with someone who has had the opportunity to try different engine oils, different grades,the tolerances that were found during the reconstruction...
  5. Jay1017

    For Sale SR20/CA18 Nistune Setup

    - S14 Zenki ECU + Type 3 Nistune - 2x R35 MAF’s - 3” Intake pipe with bung welded on This setup is compatible with both CA18DET & SR20DET (S14 Zenki only) as they share the same ecu plug. Ran on my CA18 s13 due to the ecu being more responsive than the std ecu with a nistune. Standard being...
  6. elrondo303

    ca18det shavings in oil

    hello, can someone help me out identifie these metal flakes or atleast show me the right path what to do in this situation? long story short my oil pan was leaking so i decided that i should change my oil pan gasket but when i removed the oil pan i found some metal flakes in there. overall the...
  7. Jay1017

    For Sale Garrett T25 / GT2552 (Rebuilt & Uprated)

    Freshly rebuilt Garrett T25 (GT2552) Turbo. Standard on the CA18DET engine Ideal turbo for small displacement engines, providing great response - Replacement inconel 713c turbine - New bearings, seals & piston rings - Upgraded 360* thrust bearing - .64ar turbine housing Rated for 240-250hp...
  8. M

    CA18DET dipstick tube fitment

    Hi! Anyone have a picture of the ca18 dipstick tube seated into the block? Removed mine during rebuild without taking pictures first (stupid), and unsure if I've fitted it properly again. Thanks!
  9. C

    Ca18 headers and turbo install

    Hello again, been mode active around my s13 laterly and rn im readoing my whole hot side, since my oem manifold cracked pretty bad and found out it was rewelded before: Then i bought some aftermarket 1:1 copy of turboworks one...
  10. T

    Another newb

    Hi all. I've just bought a 180sx with the ca18det engine and am looking for help, guidance and counselling on turning it up to a respectable power. In honesty, when I bought the car, I thought it were an sr20det (bought from Japan on impulse) and so I'm hoping these smaller, older engines are...
  11. midnight_purple_s13

    ca18det ignition 3 wire.

    hi i have problems with my ca18det where i dont get spark on cylinder 3. plugs and coil are ok. but i cant get an conection with ignition 3 from ecu to coil plug. so i was wondering if someone know where the ignition 3 wire goes?
  12. Jay1017

    For Sale CA18DET Custom Tubular Manifold

    Selling my custom thick wall manifold for CA18. Stock location so will work with the standard elbow/exhaust setups 1.5" equal length runners CNC'd head & turbo flanges (T2) Ideal for any high power CA! Hasn't been used yet as I've gone a different route with my engine setup Looking for £550
  13. J

    Ca18det Misfire issue

    Hello, so I’ve been having this issue with my ca18det where it will start to hesitate and misfire trying to rev over 4K. I’ve sorta narrowed it down to tps I have tested it and everything seems okay. I’ve heard it needs to be set to 0.5v closed but the issue I’m having is I can only adjust it to...
  14. S

    Ca18det idle problem

    Hi guys , had this idle issue with my s13 ever since I bought it will idle fine when cold , as soon as it gets to working temp the revs pick up to 1700-2000rpm have tried replacing the aac valve although it was a brown plug type , not sure if there is much difference It would only go up...
  15. R

    CA18DET Slow boost on stage 2 chip

    Hello everyone i got a problem with my 1991 S13 after instaling Stage 2 (Horsham) . For the chip i installed this stuff : 1. New turbo pipes (60mm) 2. new Air Filter (K&N RU-2820) with 127mm diameter ,and 76mm exit to the turbo. 3. New T2860RS (hybrid) (Model 739548-5) : -Wheel: 53.90...
  16. B

    Deatschwerks 800CC Injectors CA18DET

    Selling my unused set of DW 800CC Injectors, set is made for CA18DET S13, but should work in plenty of other cars too. Compatible with E85. Asking for 300€ OBO, Injectors are located in Finland, willing to ship elsewhere
  17. D

    WANTED 180/200sx S13

    Hi All, I currently own a Focus ST225 but looking to get an S13 I've always loved this cars and looking to get a good base. Nothing to overly speced out. My price range is around 7000 - 7500 depending on what I get for my focus my number is 07734098444
  18. Theogriffiths

    For Sale SOLD, PLEASE DELETE

    NO TIMEWASTERS, PLEASE READ THE DESCRIPTION. Any stupid offers will just be ignore, without trying to sound like a w*nker i'm bored of people offering me £800 Nissan 200sx s13 V5 Present in my name. Between the car and spare parts you could make a small fortune if you were to break it, I...
  19. B

    CA18DET FULLY FORGED, UPDATES

    hello guys, finally, after a long time, there are, I need some advice, I ordered all the spare parts for my ca18det, I wanted to get 500hp, as I had communicated, some time ago, but I thought about it, I will aim to get 300-350cv so i bought these pieces 1 - piston CP 84mm 9.0.1 2 - Eagle...
  20. Jay1017

    For Sale Rebuilt Billet T28R / 2560R

    Rebuilt T28R balanced by Best Turbos Has a 7/7 billet compressor wheel, brand new inconel turbine shaft, new BB cage, o-rings, piston rings etc. Comes complete other than the actuator, made 330+ HP on my friends SR before it was rebuilt £550 but I am open to reasonable offers
Back
Top