ecu

Hi, for sale I have a new AEM Series 2 ECU for Nissan engines. New never been used. 990€ Free shipping + Paypal fees

I've got a 3UZFE out of a LS430, about 140K on the clock, timing chain done at 125K. Transmission shifted smoothly, engine pulled strong. Harness is un-cut and have all sensors. Everything is attached to the engine, it even comes with p/s pump, a/c compressor and MAF. Could sell separately, let...

Looking for a 1jz non vvti wiring loom and igniter, Might be after an ecu too if it’s reasonably priced

Hi guys have a whole set up for sale, was running this kit on a rb25det s13. Selling due change of set up. - Owen development custom GTX3071r-HTA with tial exhaust housing used around 1000miles £1200 ono - Tial wastegate 38mm MVS £150 ono - Nistune ecu for rb25det spec 1/2 mapped at 1.15bar...

Hi, i'm searching a pnp ecu for tune my ca (2560r / stock maf / stock injectors). NO stage chip they don't work well (bad Rich afr).

I Recently got a 1jz non vvti engine, it came with an ecu which has ‘hi tech rom’ stickers all over it, does anyone know anything about these ecus? Are they tuneable? It’s hard to find any information on them also if anyone has a standard loom and/or original coil packs for sale send me a message

So I have this shitbox project car... It's a 2008 Ford KA mk1. Literally just a banger for shits and giggles. I have also semi-installed a BEE*R Power Builder type B. How is it semi installed? Grey wire is cut because its a 4 cylinder. The red wire is hooked in to the OBD-II +12v wire. (power)...

Hi guys, I was looking into installing an AEM wideband gauge in my Silvia but I’m at a crossroads, I already have a wideband sensor installed that goes straight to the ecu and I wanted to divert this to the gauge and from the gauges output, divert to the ecu, this way I only use one sensor...

Can be used for almost any build! Virtually brand new! Engine Configurations 2-12 Cylinder Distributed 2-8 Cylinder Wasted Spark 2-4 Cylinder Direct Spark 2 Rotor Engines Odd Fire Engines 2-Stroke Engines Configurable Firing Order Configurable TDC Points (for odd fire) Fueling Adjustments Up...

I'm back again with more stupid questions :D I may have a possibility to buy a Link G4 plug and play ECU for my SR20 but I'm in two minds. Mainly because it would involve selling my SR20 Power FC D-jetro and then having to add more money towards the Link (which could ideally be used in the...

Hello i want to know if somebody can help me to find what’s going on with my 1jz What happens is that the stock apfc map got un configured and doesn’t start the engine, it turns on and keep the rpm at 4,000Km/h but only for few seconds. I’m trying to find out this instruction manual but for the...

Somebody offer on??

Hi, I am looking for an ECU for a 7m-gte M/T (Yellow plugs), Turbo engine wiring loom (Yellow plug again) and a HAC sensor for a 1988 MK3 Supra, Thanks

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F283663282399

Fully functional OEM ECU with one base / board from Horsham Stage 2a. For manual gearbox, SR20DET. Price 299€ - open for offer, located in South Germany. Shipping no problem. Here more information about the board. Info...

Half way through turboing my 96 paseo , got everything bolted / plumed in and bigger injectors in , now I'm just abit stuck as to where to go from here as I'm useless when it comes to the electronic side of things obviously I'll need new sensors being a na originally but what new sensors are...

I am looking for a 7M-GTE engine for a conversion on a 1988 supra N/A, I am also looking for the engine wiring loom and ecu for manual transmision from a pre 89 car

Im selling my nismotronic red top ecu with the wiring loom all the sensors , Aem wideband with the gauge , EBC mac solenoid , 3.5 aem bar map sensor , Iat Sensor , 1 switch for hi/low boost , 1 switch for antilag or nitrus , it has boost by gear . Im giving the bluetooth mode and the tablet for...

I recently installed a chip from turbonoz in my 180sx sr20det ecu. I tried in an E5 and a 62 ecu but it doesn’t seem to be working. It’s as if the ecu isn’t reading the chip at all. I have triple checked my soldering on the manifold and the jumper CJ1 to CJ2. The red light on the ecu just stays...

Hi all, As mentioned in the title, I'm looking for a Apexi Power FC, Ecu Master or standard ecu for a manual 1JZ-GTE VVTi (or someone who can repair a broken Apexi Power FC). I you have one, please send me the details and price. Jan Willem, /close, bought a standard ECU