garrett

Hi, Im running a SR20DET with standard s15 5speed gearbox. SR20 specs: HEAD: Supertech dual valve springs TOMEI PROCAMS Solid lifters titanium Retainers ---- Supertech headgasket Mazworkz Main and Headstuds ---- Bottom: Manley rods cp pistons some special coated bearings ---- Mazwork chain...

Garrett T28 converted to a GTX2867r Gen 2 Turbo specifications: - Point milled GTX2867r Gen 2 compressor wheel - Inconel 713c GTX2867r turbine wheel - Ceramic dual ball bearing cage with brass ball retainers (upgraded over standard GTX2867R) - O-ringed backplate - Reprofiled T28 compressor...

Garrett T28 converted to a dual ball bearing centre section with a G25-550 compressor & GTX28R inconel turbine wheel Turbo specifications: - Point milled G25-550 compressor wheel - Inconel 713c GTX28R turbine wheel - Ceramic dual ball bearing cage with brass ball retainers (150k rpm rated) -...

Hey guys So I have my 1j with a couple of problems car has been working fine with my set up for a whole now but no it's doing some weird things Check engine light came on and now it's reving to about 4k rpm with little to no boost then jumps to full boost at 5k rpm and takes off, also the...

Up for sale is this freshly built Garrett GT2871r hybrid turbo Spec rundown: - 6/6 billet compressor wheel - Inconel turbine wheel - New bearing housing, ceramic ball bearing cage & seals - Polished compressor housing inlet - Powdercoated black compressor housing - Ported internal wastegate for...

Refreshed Garrett GTX2860r Gen 2 .64ar - New compressor wheel - New Inconel turbine wheel - New replacement turbine housing, internal wastegate has been ported to improve boost control - Built in 1mm restrictor Component & VSR balanced (twin plane) Comes complete with actuator ready to use...

Selling this rebuilt Garrett GT2554 (T25G, 180sx SR20) The spec of the turbo is as follows: - Inconel turbine - 360* thrust bearing upgrade - Updated brass journal bearings - Powdercoated actuator Compressor spec: 41/54mm Turbine spec: 42/53mm Turbine housing is T2 flange with 5 bolt outlet...

Freshly rebuilt Garrett GTX2863r (standard replacement) not often you come across these Following work has been done: - New GTX2863r Compressor Wheel - Inconel 713c GTX2863r turbine wheel - New bearing housing, ball bearing cage & seals - New standard replacement turbine housing (.64ar) with...

Looking for either of the above, must be in non working condition. Happy to buy parts as well such as housings and so forth

Freshly built & modified Garrett GTX2867r Gen 2 Turbo spec below - Custom forged billet GTX2867r Gen 2 compressor wheel with extended tips, larger inducer trailing angle & smaller root design to improve flow - Inconel 713c GTX2867r G2 turbine wheel - New bearing housing, ball bearing cage...

Reconditioned Garrett GTX2860r Gen 2 that has had all it’s working components replaced, info below - New compressor wheel - New Inconel turbine wheel - New bearing housing & ceramic ball bearing cage - New replacement turbine housing, internal wastegate has been ported to improve boost control...

Selling a freshly built Garrett GT2871r Hybrid (52trim) turbo The spec of the turbo is as follows: - GT2871r 6/6 52trim billet compressor wheel - Inconel GT2871r turbine wheel - Brand new bearing housing, ceramic ball bearing cage & seals - Brand new turbine housing - Ported internal wastegate...

Hey guys I have a few turbos for sale that are just sat on the shelf gathering dust Garrett GT2871r Hybrid - New The spec of the turbo is as follows: - GT2871r 6/6 High flow billet compressor wheel - Inconel GT2871r turbine wheel - Brand new bearing housing, ceramic ball bearing cage & seals -...

Selling a freshly built GTX2867r Gen 1 The spec of the turbo is as follows: - GTX2867r G1 11+0 Billet compressor wheel - Inconel GT28r turbine wheel - Brand new bearing housing, ball bearing cage & seals - Brand new turbine housing, internal wastegate has been ported to improve boost...

Genuine Garrett GT3071r used but in great condition, no play and both turbine and compressor wheel are immaculate. Turbine housing is .86ar and has 3 bad studs in and is cracked around the flapper. Can replace studs before sale for £30 extra if you still want to use the housing. Compressor...

Selling my freshly built GTX2860r Gen l, the spec for the turbo is as follows: - GTX 11/0 Billet compressor wheel - New bearing housing - New ball bearing cage - Upgraded inconel turbine wheel - Compressor wheel size is 46/60-65mm (extended tip) - Standard GT28 turbine Turbine housing is...

Hi guys have a whole set up for sale, was running this kit on a rb25det s13. Selling due change of set up. - Owen development custom GTX3071r-HTA with tial exhaust housing used around 1000miles £1200 ono - Tial wastegate 38mm MVS £150 ono - Nistune ecu for rb25det spec 1/2 mapped at 1.15bar...

Lads and Gents, i want to present my GT86. And also me. This is me. Sven I bought this car back in 2013 as a display car from the Dealer. At this point it was a half year old and got 10k km on the clock. I ordered new taillights and other rims even before i got the car. The next mod was...

Got these two freshly built T28R’s for sale. They are both built from all brand new parts since the old cores ended up being scrap. Both were balanced via TT VSR after. Part list includes - New core New upgraded (inconel) turbine wheel New ball bearing cage, pin, seals & piston rings New...

Hi everyone, I've been planning to upgrade the turbo in my SR20 to a GT2871r. It is a road / drift car setup I'm looking for around a reliable 300-350bhp. I would like your advice and opinions to choose the best A/R ratio to reach my requirements. I got the options below, With the standard...