help please

I've been trying to track down this problem for a while now with my 1995 Miata. I continue to run into an issue of seemingly not having enough caster at increased steering angle. When I first added some steering rack spacers years ago, I noticed an issue with my steering where the car would...

Hi guys, looking for some help and any ideas possible. The driveshaft on my E46 drift ace snapped the other day but it has snapped the spline end that goes into the diff. I’ve managed to get the drive shaft out but the spline is still stuck in the diff due to the clip that holds it in. Tried...

Hi All Currently part way through 328i Conversion on my 316ti compact, I have got the M52B28TU engine bolted in but I cant figure the wiring side of things out. The donor car was a 1999 E46 coupe fly by cable, the compact is 2002 fly by wire, There are a couple of connectors in the DME box...

As the title says.. i need a manual gearbox for my s12, im running the ca20e engine. DONT say ''swap to ca18 or sr20'' i KNOW that.. So my question is, what will fit the ca20e? A ca18? I cant seem to find a manual ca20e trans in europe, and i got told that it only good for 200hp, thats not...

Hi everybody, I recently bought this 1990 mazda miata and have plans to drift it. Took a look underneath and saw this on the frame rail (or whats left of it) Need opinons :cry: Should I cut the rail out and weld in a new one? should I take it to get fixed somewhere? Should i just drift it...

:thumbs:I am just starting to drift and i need some help on getting more angle. ive seen multiple people move the postioning of their tie rods further in on their hubs or spindles. are there any other ways that you guys know of??? cutting the bump stops back? please help me slide more...

I have bought a bolt in 6 point Fabricage rollcage for my s13. Does anybody have their cage mounted in their car and able just to take a few pictures of exactly where its mounted in the car at the bottom of each leg. Just want to see a few and check that its all okay before I weld in the...

I've tried posting some wheels up a couple times and they're still not getting accepted? is it because I'm new to the forum ? i don't know how to PM any of the mods so any help appreciated ;) my thread was for the Work Meister S1Rs if any mods read this :)

Hi, Im looking to get a AE86 levin, however could you guys help point out any differences between the UK spec and japanese spec, a mate bought a toyota of some-sort (import) and the chassis was half the thickness, the steering linkages were made of plastic rather than phosphor bronze as in the...

I'm currently looking at importing a car from Japan to the UK Does anyone know of the closest port to Scotland (easier for me to get to) that I can get the car shipped to? I'm thinking of going with Kleerfreight as the customs agent however they only cover Southampton, Tilbury, Bristol and...

Hi, this isnt a drift picture but is a RX7.. a family member does vinyl wrapping and wants to find out who done the work on the mazda.. if anyone could help me find out who done the art work or who owns/ owned the car would be a HUGE help! thanks a bunch!:D

I need anyone who is selling or renting a trailer in or near kings lynn!!! This is a real emergency!!!! I have to pick up a 200sx s14 on the 31st of this month!!! Help anyone!!!!!

this is for my ford focus which i know isn't rear wheel drive but it is the daily driver ANYWHO, couple days ago the bite point went down towards the floor much lower than normal - and had a lot of play in the clutch pedal. been having a few difficulties changing down a gear past 2 days. TODAY...

ae85 project help please hey everyone i recently brought a ae85 with a bluetop 4age and bucket seats. i lockd the diff and brought some bc gold adjustys and i was curious to know how to slam it on its arse i put the rear adjustys in right to the bottem but still seems higher? whats up with...