wiring

Hi all, I've got a 1991 200sx which I bought as a rolling shell. I'm now in the process of putting in a CA18DET from another S13. I've got the engine in and I'm now trying to wire it up with the mess of wires I have. I'm missing quite a few bits which is making it quite difficult. I was...

So I have this shitbox project car... It's a 2008 Ford KA mk1. Literally just a banger for shits and giggles. I have also semi-installed a BEE*R Power Builder type B. How is it semi installed? Grey wire is cut because its a 4 cylinder. The red wire is hooked in to the OBD-II +12v wire. (power)...

Hey, so I just bought an HKB boss kit for my supra that retains cruise control, and I'm having some trouble figuring out where you are supposed to solder the wires to on the controls. I don't know if it was supposed to come already soldered on but mine did not and I'm wondering which solder...

i am in search or a pre facelift yellow plug engine harness for a 7mgte mk3 supra preferably a manual if anyone has one available please Thanks

Hi all I think I need to swap some wires around with the I think it’s the f3 plug correct me if I’m wrong Rb25 engine loom is all in my car , but I seem to have no power to ecu (power fc , controller don’t turn on ) and no fuel pump prime or wipers Does anyone have the pin out diagram of the...

Half way through turboing my 96 paseo , got everything bolted / plumed in and bigger injectors in , now I'm just abit stuck as to where to go from here as I'm useless when it comes to the electronic side of things obviously I'll need new sensors being a na originally but what new sensors are...

I am looking for a 7M-GTE engine for a conversion on a 1988 supra N/A, I am also looking for the engine wiring loom and ecu for manual transmision from a pre 89 car

Hi guys looking to sr20 an is200 but i was wondering about a few wiring issues. Ive no problem fitting the engine and getting it started but i want it as a road car and as such i need the dash working for the nct (Ireland's mot) im sure people have done it but would like the info on getting all...

Hey guys, Recently go another 180 and I'm having a few problems. When I collected car I could hear clicking from under bonnet but I didnt think much of it (sounded like a relay). The car drove well for most of the 400 miles home then suddenly the engine would cut in and out while driving...

2000 S14a Black Top. Front right tyre buffed through engine loom as they tend to so I cut damaged ends and twisted wires to get the car to run. I then one by one cut and extended each wire and routed the loom through the engine bay. The car now turns over with spark but won't start. Fuel...

Hello my cluster for my s14a cluster gauges don’t work I’ve checked the fuse. All the lights everything works apart from the gauges. Anyone know what could be the problem, maybe a wiring diagram for the cluster too If someone could help be much appreciated

Recently bought a redtop PS13 engine that came with a loom and 62 ECU, not needed as I already have both. The loom looks to need some TLC but came off of a working engine so am under the impression it's in working order. The ECU looks fine but has an UPLINE sticker on the front. Can't find...

So, im looking to build an RB25 powered S14A. Its a track only car and i want to run as little wiring as possible. My question- Has anyone ever run an RB on a bare engine loom, Fuel pump wiring, ECU power & ground etc. it will be running a standalone, and any thing else i need will be working...

Hi all, So, to set the scene, I have an RPS13 180sx. The car is a 96 model and has an SR20DET Blacktop engine. The car is running an aftermarket FMIC, new uprated coil packs, an aftermarket air filter, a t28 turbo, braided turbo lines, a smaller battery (to accomodate larger intercooler...

Yo dudes.. Just wondering if anyone has come across this before... I'm doing a 1uz conversion.. The car is a jdm import and was originally an NA Auto.. Iv discovered that the F4 is wired differently to that of Turbo Manual S14's.. Anyone got or know of a reasonably accurate Pinout diagram...

i am under goin a manual conversion and yes it is very hard to get infor that isnt based on US (RHD) soarers.. kinda stuck on things like when you installed the clutch pedal does your clutch master cyl hit the CAT ?? whick pedals fit? Also can anyone help me with wiring the auto box out...

My speedo doesn't work... I got a uk spec s13 with rb25 engine and box, s14 rear subframe, diff, shafts etc... S14 hubs. This car is my daily so it would be handy to have a speedo... Any tacho/speedo nerds out there? ;)

Hi, I signed up to the forum here as it seemed a good place to find some reliable information. I purchased a 1992 Toyota Soarer that was a manual transmission car, with no engine, transmission, engine wiring or ECU. I'm looking at putting a 1JZ-GTE back in with an r154 transmission. It seems...

1600 watt, never been used Black Air II with wiring and enclosure already set up blah blah, 100 quid, pick up only, somerset area, will send pics if required. Thank you.

Am about to swap the standard AFM on my redtop sr20det to a z32 AFM. Anyone have a guide or knowledge on which wires go to where on the z32 plug? Cheers