180sx

Hi guys, I've decided to bite the bullet and change out the SR in my S13 for a 1JZ-GTE VVTi. This will be the build list, any ideas will be much appreciated: - 1JZ-GTE VVTi w/stock loom and ECU - PMC JZ-M57 gearbox adapter plate w/custom flywheel - S14 subframe - Clark Custom engine mounts...

Selling my 180sx - S15 front end conversion as my plans have changed . Front bumper , 2 x vented wings and Fiberglass headlight blanks . All parts were only painted in Nissan KH3 black last week . The entire kit is second hand but in very good condition , one or two blemishes but no chunks...

Hi and thanks for looking at this advert for my Nissan S13. Wasn't planning on selling her but I moved house and now walk to the train station, so the car very rarely gets used. Therefore I thought I'd see if anyone wanted her. The owner before the last was an older lady who kept getting Nissan...

I want a 200sx s13/s14, please add your offers!! (If it's stock better) thanks!!

heyaaaa im looking for s13 chuki side skirts, i know they are hard to find, at least im having a lot of problems finding it. im ok with replicas as well... can anyone help out? thanks

Need square style front and side indicators for Nissan S13!

Any rust free boots for sale? As close to york as possible but willing to travel or meet Cheers Chris

Hi all, I'm looking for an S13 ABS pump with n/s/f (front left) brake line that goes from the pump to the wheel arch. Images below with part number which must match. Must be in working order with no leaky seals as looking to replace current pump which is leaking.

Hi! Recently purchased my first S13, a fresh-ish imported Sil80 Its come with some nice goodies on it, some RAYS Compionato's, Blitz coilovers, Apexi Exhaust, Sparco seat and a few hks bits under the bonnet, air filter etc...Very Clean underneath Only 'problem' is its a non turbo SR20DE My...

After taking apart my s13 I've come to the conclusion that the shell isn't salvageable so I'm now looking for a new one, should be straight and shouldn't be a rust bucket.

NOW SOLD

Full S13 exhaust from a 180sx for sale Comes with standard elbow, 3" downpipe, 3" midsection & 3" rear section with 4.5" backbox. No holes, all flanges are straight and cleaned up and just want rid now as I'm keeping the 13 standard. £60 collected from Stoke on Trent

As in title I'm after a pignose bumper and bonnet , can buy or swap for for BN sports bumper and bonnet with screamer pipe hole in. cheers Dan

Hi guys, for sale I have a pair (2) TE37's. I recently bought a full set, only need two of them so these are up for sale. Condition is almost immaculate for their age, I'd say 9.8/10. Comming with stickers and valve stems OG bronze color 5x114,3 18x9.5+12 Price 1170€ Free shipping in UK and...

HI all, I've a DCC from 180sx with arnes and else but I've not A/C into my car. Also, for a normal install you have to adapt: - Digital climate control unit - DCC sub harness - Mix door motor (At first I think I've to put on OPEN mode? so I dont need it) - Ambient air temp sensor - Cabin air...

Hi there, greetings from Norway. New member and this is my first post here. :) I have a Nissan S13 180SX that I bought I a while ago. For the most part a fully prepped drift car which won't be used on the road. Just some bugs I have to iron out before the season starts again. Thinking of...

After an s body rolling shell. Preferably an S13 but open to anything. What's out there? Cheers

Hi All, For sale is my pride and joy which I have put countless hours into for the past 18 months. Imported 1996 180sx RPS13 in White. The shell has 140k kms on it but is super straight and very clean underneath. The engine was supplied by JDMDistro earlier this year and was supplied with 150...

Hi there, selling a pair Cr Kai's in Work Metal Bright color. Imported from Japan through Streeter last year to match my 17" front setup (already sold). 5x114.3 2x 18x9.5+12 WMB color was extra $$$. As far as I know the color discontinued on the Kiwamis now. Selling because I sold the car...

So. Generic tubular manifold, stock t25g = hot side intercooler piping no longer clears manifold? Anyone gone through that and found a solution? Manifold is cheap and purely for messing around with so I’ll bash headers if necessary, just wondering if it’s just me with this issue