engine

Hi all, Got a fresh import rx7 non rolling shell for £700, very clean example unregistered fresh import. As well got a complete twin turbo 13B engine with gearbox £2000 with video of it running available. Came off fresh import from Japan done 98000 km but runs perfectly fine without any...

For sale are a few CA18DET parts left over from an unfinished project. Due to starting a new project I have had to stop this one due to funds. For sale is my Wossner Forged pistons and engine block machined to suit 84mm with rings and gudgeon pins, pistons brand new unused. £450 all...

Posting on behalf of a friend. More than happy to answer any questions if you, for some reason, don't want to text him. Breaking his 1.8IS mx5. Had the rear end badly damaged cosmetically. There's a lot for breaking but this ad is just for the engine and gearbox 146bhp VVT engine with I'm...

Hi guys, I have been working on re building a full CA18DET engine and have been collecting various parts. Now due to unforeseen circumstances I have decided that I have to sell up my project. I have the following parts for sale for collection only from Fenton in Stoke on Trent. Wossner...

Ideally after a 6 pot e30 engine to just drop in and go! Would need all bits required. What have people got? Based in Essex

After a CA, can just be bare engine, as I have mani's and turbo etc. No knocks!!! As close to Essex as possible. Cheers

I need an engine asap for my s14 got cash waiting. Would like a stroker or a forged block. But may even just use a standard. Pm me please or message me on 07718486987

Im re-building the engine on my z32 and doing various mods, but im wondering whether its a good idea or not to install aftermarket underdrive lightened pulleys, ive found some good quality ones from the USA called unorthodox racing pulleys, but ive heard alot of debate as to whether they are a...

CA18DET plus parts, boost controller etc. Engine is on 110k miles, It pulls hard and is in good condition. Comes with complete, with turbo's, and inlet, and clutch plus plate. Here a video of it running in car. It is unmodified and ran on stock boost for all its life. External mods were...

Toyota Aristo Mkll Good Engine, 147k on clock, some kms some miles I believe. Body is ok, had few scuffs and been touched up badly, front wing has dent at front. Chassis is good and rust free from what I have seen. Balljoints and bushes need doing. Interior is Grey Leather seats with...

Got a full ca18det bored to 84mm forged wisecos, brand new acl race bearings on all rods and mains engine done 0 miles since rebuild.as head gaskets leaking water into cylinder 3, think.decks warped as whole cylinder head was refurbed and skimmed, got pictures and receipts for engineering...

Yo dudes.. Iv got this lot, it's most the parts you'd need to make a 3sgte into a RWD format, with a decent 6spd manual box. This is a very cost effective way of getting a near 'bolt in' package to turbo your Altezza/IS200 or whatever.. In my opinion, this is a better option than turbo'ing...

Altezza Beams 3SGE Engine & 6spd Manual Trans Details: Just broke an Altezza for parts, car was a non runner due to exhaust manifold being removed, previous owner fitted a turbo kit then bailed on the project before finishing it. Engine has wiring loom, ECU, Auxillaries, etc.. Mileage is...

I have an s13 shell looking to rebuild the whole thing, anyone have a ca18det engine in decent condition, they wanna sell, if close I could pick up or arrange delivery thank you

Breaking e36 323 coupe silver plenty of cheap parts!! 2.5 engine cheap! E36 323 up for breaking lots of parts available Heres a few prices for parts collected (norwich) i can post out anything you require just pm me! Engine £150 gearbox £50 interior £50 diff £45 prop shaft £35...

Looking for a forged or strokered sr20det. Must be warn in or have warranty. Give me your offers. Need one asap. Could do with a new gearbox aswell

Forsale: Toyota 2JZGTE Engine - R154 Gearbox - JZ>R154 Bellhousing 2JZGTE Engine Package: £1950 Engine has covered just 80k Kms. Supplied by Garage-D Complete running engine - 1j Loom & ECU - Auxhillaries etc - Good Condition Turbos Engine pulled very well, I drove the car before...

Forsale, Pair of 1jzgte Turbo's These are off an engine I'm rebuilding, no longer needed as now single turbo. Iv not seen these running so sold as seen. There is virtually No play in the shafts, the impeller wheels all look to be good, and no evidence or any leaks internally or externally...

Just bought a standard low mileage (36'000) s14a and i'm not sure what oil to run the engine on. I haven't been able to find much information and my local garage doesn't seem to know either for some reason. If anyone could help that would be great. It's the SR20DET engine. Cheers.

Yo dudes, Just seeing if there is any SR20det conversions going? Id want a decent running engine with all auxhillaries & turbo, gearbox, loom, ecu, etc etc.. Cheers dudes.. Dale